How long after pressure washing a deck can you stain it

After a deck has been power washed it will have some retained moisture within the wood. It’s important to let the wood dry thoroughly so none of the water that soaked into the wood gets trapped under the stain. In perfect drying conditions, 48 hours is enough for the wood to get to where it needs to be before staining.

How do I know if my deck is dry enough to stain?

To determine if pressure treated wood is dry enough to stain, try the “sprinkle” test. Sprinkle water on the wood: if the wood absorbs it within 10 minutes, plan to stain as soon as possible. If the water beads or pools on the wood surface, the wood needs more time to dry.

Can you stain a deck immediately?

Absolutely. You can stain a new deck immediately after installing your deck, but this is not the best time to do it and here’s why: the lumber is still too wet. The best time to stain a new deck is 3 to 12 months after installing it.

Is it OK to pressure wash deck before staining?

There is a common misconception that just pressure washing a deck prior to staining is all you need to do in order to prep your deck for stain. Pressure washing can help, but if you want your stain to last, using a good deck cleaner and brightener on the deck prior to pressure washing will provide you the best result.

Can you pressure wash and stain a deck in the same day?

DPI Pressure Washing recommends you wait 72 hours following cleaning to stain your deck. If it rains on one of the days afterwards, you’ll have to wait again, but it will be worth it.

Why you should not pressure wash your deck?

Ideally, power washing a wood deck will not ruin the wood and etch or erode the softwood fibers. However, when wood gets wet, the fibers may become raised, creating a rough surface. This is a particular problem on handrails, where the raised fibers can lead to splinters. Make sure the wood is dry before sanding.

Can you stain a deck 24 hours after power washing?

Staining your deck can be an affordable way to restore its appearance. … After thoroughly cleaning and power-washing your deck, allow it to dry for at least 24 hours before applying the stain. Whether your stain is latex or oil-based, the right application technique can bring out a wood deck’s warmth and beauty.

How many dry days do you need to stain a deck?

You will want to set aside a minimum of two days, including drying time. If your deck needs to be power washed, or if the boards on the deck need replacing, you may want to set aside another extra couple of days. Be sure to have all of your supplies ready well ahead of time.

Can you stain a weathered deck?

When you are done repairing, cleaning and stripping the deck, it’s finally time to stain that weathered wood. … A semi-transparent stain will impart a little color to the deck wood while still allowing the grain to show through. If you need to replace boards in the decking, you could opt for a solid stain.

How long does it take to stain a 20x20 deck?

The average time it takes to stain a deck is 4 hours per 100 square feet. Staining a deck takes two-days. The first day is moving furniture, stripping, power washing, sanding, and repairs, while the second day is applying stain and sealer. An average deck takes 10 to 15 hours of labor.

Article first time published on

What month should you stain your deck?

The best time to stain your deck is either the spring or the fall. If you stain your deck in the summer, make sure you do it out of the direct sunlight. Applying a deck stain in direct sun will cause the stain to dry to quickly and can result in premature stain failure.

Can you ruin a deck by pressure washing?

The impact of washing your decks under high pressure is profound in softer materials such as PVC. The pressure washer can significantly engrave the PVC on the deck if you use unreasonably high pressures during a routine washing exercise. Washing a composite deck under high pressure can also lead to extreme damages.

What if it rains the day after I stain my deck?

Splotchy Appearance If it rains within 48 hours after you apply the stain, the water will soak into the wood pores and try to displace the stain. This will result in a splotchy surface rather than an even tone. If it rains right after you apply the stain, the stain will peel and flake off.

Do you have to stain a deck after power washing?

As a general rule, you should wait at least 24 hours to stain a deck after power washing. You want the deck to be completely dry before you put any sort or coating on top. … Waiting 24 hours makes sure that your deck is completely dry, but really, once it’s dry, you’re ready to stain.

What happens if I don't power wash my deck before staining?

If you decide not to power wash beforehand, not only will your new paint not stay for very long, but your old paint will still be underneath. Pressure washing will not only remove the dirt and grime, but it can also remove old, chipped paint that may cause discrepancies in you new paint job.

Is 1800 psi enough to clean deck?

For cleaning a wooden deck, you’ll be best served by using the lowest pressure setting that’s still effective. For soft woods like cedar or pine, this is usually about 500 to 600 psi. For harder woods, it can go up to 1200 to 1500 psi. … Never get closer than 12 inches from the deck unless you’re using low pressure.

Can you stain a deck without removing old stain?

If you’re wondering how to restain a deck without stripping or sanding the old stain off, we can help. To avoid stripping or sanding the old stain off your deck, thoroughly clean and rinse it, and then let the wood dry for 24 to 48 hours. Apply the same (or darker) stain color or tint from the same manufacturer.

Is it better to paint or stain an old deck?

While staining may take less time than painting, painting often does a better job of filling the cracks, covering imperfections, and provides longer lasting protection. Paint also is typically more rot resistance and does a better job of preventing mold and sun damage.

How many coats of stain should you put on a deck?

The general rule of thumb is to apply only as much deck stain as the wood can absorb. Typically this will be 2 coats, unless your dealing with extremely dense hardwoods which may only be able to absorb 1 coat of wood stain.

What is the best temperature for staining deck?

Apply stain only at the proper temperature. For most stains, 70 degrees Fahrenheit is the optimum, with the safety range from 50 to 90 degrees Fahrenheit. Stains do vary, so check the label first. Avoid high humidity and staining on hot surfaces.

Why is my deck sticky after staining?

“A sticky or tacky deck is usually due to over-application or failing to wipe the excess stain from the surface of the wood. … Rinse thoroughly with a garden hose and spray nozzle, and let the wood dry. This removes any tackiness or residue.”

When should you not stain a deck?

Apply stain when the temps are between 50 and 90 degrees, and avoid staining in direct sunlight if possible. Sun dries out stain quickly and can create uneven color or brush marks. Check the weather forecast to make sure you have several dry days ahead.

How long does it take to stain a 12x12 deck?

Applying paint or stain will take a few hours for each coat, with a day allowed in between for drying time. From start to finish, it could take three days to complete a small deck and up to two weeks for a larger, more complex job.

What to do after Powerwashing a deck?

After you’ve power-washed the entire deck, rinse all of the wood with plain water to dilute and neutralize the stripper. If there’s still debris trapped between deck boards, such as leaves or twigs, remove it now (Photo 3).

Is it OK to waterblast a deck?

Hit The Deck We don’t recommend waterblasting timber decks because you immediately break down and destroy the fibres in the timber. If you looked at these fibres under a microscope, they would look like miniature ‘pick up sticks’.

Do you sand or pressure wash decks first?

DO sand your deck before sealing. At that point, lightly sand the surface to remove splintery or fuzzy patches caused by pressure-washing the deck. A pole sander with 80-grit sandpaper will suffice; a power sander is overkill. Then seal the deck to protect from cracking, cupping, and warping.